Overview
Add Device puts a new Verdi device on your dashboard in about a minute. You scan its QR label, mark where it sits on the map, tell Verdi what is plugged into it, and name it.
Use it from a phone in the field or a computer at app.verdi.ag. This article is for User and Admin accounts.
What you set up depends on the device:
Device | What you set up |
|---|---|
Block Controller (Gen 4) | Location, plus one valve or pump and the zones it serves |
Micro-Block Controller | Location, plus up to two valves and their zones. Add no valves for a sensor-only Micro. |
ePlant TreeTag dendrometer | Location and the zones it monitors |
SDI-12 Remote Telemetry Unit | Location and the zones it monitors |
Gateway (Gen 1 or Gen 2) | Location and name only |
Davis weather stations are connected through WeatherLink, not Add Device. See Davis Weather Stations (WeatherLink).
Before you start
Have the device in hand. You need its QR label, or the Device ID printed beside it (for example, eui-fcc23d000042fca3).
Leave the battery disconnected. Connect it at the end, after the device is saved.
Check your zones. Valves and sensors are linked to zones on your map. If a zone you need is missing, contact Verdi support before you start.
Select the right account. If you manage more than one account, choose it first. Add Device is unavailable until an account is selected.
Allow camera access in your browser when asked. The camera reads the QR label. See Troubleshooting if the camera does not open.
Add a device
1. Open Add Device
On the map, tap + Add Device.

2. Scan the QR code
Hold the device's QR label inside the green frame. Verdi reads it automatically and moves on. Tap Swap Camera to switch cameras.
Label won't scan? Tap Manually Enter Device ID, pick your device type, and type the ID printed beside the QR code. You can leave off the "eui-" at the start.
Asked to pick a device type? Some labels match more than one type. Choose the one that matches your device.

3. Place the device on the map
Tap the map where the device is installed. A pin marks the spot and its coordinates appear under Position. Tap again to move it, then tap Confirm Location.
Place it carefully: this pin is where you will find the device on your dashboard.

4. Add the connected equipment
Tell Verdi what is wired to the device. Equipment (0/1) means one port is free.
Tap Add Equipment, then choose Valve or Pump. Micro-Block Controllers take valves only, so they skip this choice.
Nothing wired yet, or a sensor-only device? Tap Skip Connecting Equipment and go to step 6.

For an ePlant TreeTag or SDI-12 unit, you choose the zones it monitors here instead, then go to step 6. Gateways skip straight to step 6.
5. Choose the zones
From the dropdown, select every zone the valve irrigates. For a pump, select every zone it supplies. Selected zones turn green on the map. Tap Save.
Back on Connected Equipment, check your list. Tap the gear to edit or the trash can to remove. Add more equipment if a port is still free, then tap Continue.

6. Name and save
The device is named after its ID by default, such as D-TEZ-620. Rename it to something your team will recognize, like "Block E Valve".
Check the device type, EUI, and connected equipment. Tap the pencil to change equipment. Then tap Confirm & Save.

7. Connect the battery
The device is registered. Connect its battery now so it contacts Verdi right away. The screen shows how long the first connection should take, about 6 minutes for a Block Controller (Gen 4).
You don't need to wait. Tap Add Another Device to keep going, or See This Device to open its Device Card.

After registration
The device shows on your map right away. Its connection details appear on the Device Card once it first contacts Verdi.
Micro-Block Controller: to make it contact Verdi immediately, hold a strong magnet against the back of the device until you hear a soft click.
Gateway: there is no time estimate. The gateway is confirmed once another device reports through it.
Changing zones or equipment later: open the device's Device Card.
For wiring and mounting, follow the Block Controller Installation guide.
Troubleshooting
The camera doesn't open. Your browser needs camera permission for app.verdi.ag. Allow it, refresh the page, and try again. Or use Manually Enter Device ID.
iPhone or iPad: Settings > Safari > Camera, set to Allow or Ask.
Chrome (phone or computer): tap the lock icon in the address bar, open Site settings, and set Camera to Allow.
Safari on Mac: Safari > Settings > Websites > Camera, and set app.verdi.ag to Allow.
The device ID isn't accepted. Check it matches the ID printed beside the QR code, character for character.
The device is already registered. If it is on your account, find it on the map or with Search instead of adding it again. If it belongs to another account, contact Verdi support.
I put the pin in the wrong place. Before saving, tap the back arrow to return to the map. After saving, move the device from its Device Card.
I closed Add Device partway through. Nothing is saved until you tap Confirm & Save. Start again from + Add Device.
The device hasn't connected after the estimated time. Check the battery is connected. For a Micro, use the magnet. If it still hasn't connected, contact Verdi support.
Need help? Email support@verdi.ag or call (855) 945-5628.