--- title: "Pump Relay Installation Guide" slug: "pump-relay-installation-guide" updated: 2026-03-10T21:03:35Z published: 2026-03-10T21:03:35Z canonical: "docs.verdi.ag/pump-relay-installation-guide" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.verdi.ag/llms.txt > Use this file to discover all available pages before exploring further. # Pump Relay Installation Guide ## Introduction (Estimated time for setup —> 5 - 10 minutes per device and relay, assuming just mounting and connecting wires) Verdi engineers a wireless and battery-powered irrigation controller (Model: Block Controller). It has a 100ms pulse output that can switch a latching relay into an open or closed position. ## Datasheets Here is a datasheet of the Verdi-supplied latching power relay (Model: RT314A12): [https://www.te.com/en/product-8-1393239-0.html]( https://www.te.com/en/product-8-1393239-0.html) Here is a datasheet of the Verdi-supplied DIN Rail relay socket (Model: RT78726): [https://www.te.com/en/product-6-1415035-1.html](https://www.te.com/en/product-6-1415035-1.html) ## Control Relay Wiring The control relay provides a normally open (NO) and normally closed (NC) for the purpose of controlling pump starters, VFDs, and general purpose automation equipment ## Warning and Precautions The Verdi pump control relay is provided as a stand alone dry contact relay. The installer is responsible for providing any fusing and/or protection circuitry appropriate for the connected load. ## Electrical Specifications Rated Voltage **250VAC** Rated current (UL) **16A** *see the relay data sheet for full specifications ## Operation The operation of the control relay via the interface buttons and Verdi dashboard follows nomenclature aligned with piping systems, that is the *OPEN* button will actuate the control relay and the *CLOSE* button will deactivate the control relay. ## Standard Wiring Wire the Verdi Block Controller's right most wire (Red Pulse +) to the control relay's A1 terminal, and the adjacent wire (Black Pulse -) to the control relay's A2 terminal. ![](https://cdn.document360.io/21bcacda-1800-45ee-8df3-7d1d6186e001/Images/Documentation/block controller relay lq(3).jpg?sv=2026-02-06&spr=https&st=2026-11-19T04%3A38%3A16Z&se=2026-11-19T05%3A38%3A16Z&sr=b&sp=r&sig=F6bYcuGnANBvvbsow8ERbHGPhZs3Wt2hE%2F6HyJfZU3Q%3D) Verdi Block Controller Wired to DC Latching Relay for Pump Control ## Hand Off Auto Switch Connect the external contactor terminal of a Hand-Off-Auto (HOA) switch to the common (C 11) and normally open (NO -12) contact. The operation can be tested by energizing the circuit, putting the HOA in the auto position, and pushing the *OPEN* button on the Verdi Block Controller to start the pump. pushing the *CLOSE* button will turn off the pump. ## Test When you click the open button on the Block Controller, the contacts of the relay should close, and the pump should turn on. When you click the close button on the Block Controller, the contact of the relay should open, and the pump should turn off. We understand this is confusing, but it was designed this way because most block controller installations are used on solenoid-actuated valves, where open refers to valve open. ## Example Setup ![Verdi Pump Relay Installation](https://cdn.document360.io/21bcacda-1800-45ee-8df3-7d1d6186e001/Images/Documentation/Verdi Block Controller_Web Carousel_25.01.25.png?sv=2026-02-06&spr=https&st=2026-11-19T04%3A38%3A16Z&se=2026-11-19T05%3A38%3A16Z&sr=b&sp=r&sig=mHucKiCd7EZRTlVzxrJmVBS8JMs2OsOXztwtIbHupJM%3D) Verdi Pump Relay Installation Reach out to Verdi support at support@verdi.ag or (855) 945-5628